Plp 2875014 Lite Tension Dead-End Adss .310-.341 *Order Minimum* 25
Available*
Item # 30182486
Model # 2875014
$23.04
financing available. Learn More
* Notes on Availability:
If item is in stock, it will ship same day.
Lead times vary, contact us for more info.
(Images may not be of the actual item being sold.)
- Product Description
- You Might Also like
- Recently Viewed
Generic
Class
Group
Type
Manufacturer
LOT
Deadend
Material and Supplies
Hardware- Screws- Bolts
Clamps
Preformed Line Products
Warning: This product can expose you to chemicals, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.govProduct Description
Plp 2875014 Lite Tension Dead-End Adss .310-.341 *Order Minimum* 25
Plp 2875014 Lite Tension Dead-End Adss .310-.341 *Order Minimum* 25
P/N 2875014 Preformed Line Products Lite Tension Dead-End Adss .310-.341 *Order Minimum* 25
The Fiberlign Lite Tension Dead-End Is A Dielectric Dead-End Designed To Terminate Short-Span, Low-Tension Adss Fiber Optic Cables In Low-Voltage Environments. Its Single-Layer Component Design Offers An Economical Solution For Very Light Loads. The Product Effectively Transfers The Low Axial Load On The Cable At The End Of The Dead-End Legs To Low Uniform Radial Compression Near The Dead-End Loop.
Small Diameter Wires That Comprise Each Dead-End Are A Mixture Of Aluminum And Aluminum-Clad Steel That Provide Superior Fatigue Strength To Ensure Long-Term Performance
Dead-End Legs Have A Pliable Latex Coating And Flared Rod Ends To Avoid Scoring Or Abrasion To The Cable Jacket During And After Installation
Dead-End Loop Will Fit A Minimum Cable Diameter Of 1-1/2" (38.1 Mm) And A Maximum Of 2-1/4" (57.1 Mm)
Designed To Fit Over Common Guy Wire Dead-End Pole Fittings • Extended Dead-End Loop Reduces The Need For An Extension Link • Optimized Compact Length That Allows For Fast And Easy Installation
Can Be Used On Most Brands Of Adss Cable That Have Low Strengths And “Standard” Jackets
Plp 2875014 Lite Tension Dead-End Adss .310-.341 *Order Minimum* 25
P/N 2875014 Preformed Line Products Lite Tension Dead-End Adss .310-.341 *Order Minimum* 25
The Fiberlign Lite Tension Dead-End Is A Dielectric Dead-End Designed To Terminate Short-Span, Low-Tension Adss Fiber Optic Cables In Low-Voltage Environments. Its Single-Layer Component Design Offers An Economical Solution For Very Light Loads. The Product Effectively Transfers The Low Axial Load On The Cable At The End Of The Dead-End Legs To Low Uniform Radial Compression Near The Dead-End Loop.
Small Diameter Wires That Comprise Each Dead-End Are A Mixture Of Aluminum And Aluminum-Clad Steel That Provide Superior Fatigue Strength To Ensure Long-Term Performance
Dead-End Legs Have A Pliable Latex Coating And Flared Rod Ends To Avoid Scoring Or Abrasion To The Cable Jacket During And After Installation
Dead-End Loop Will Fit A Minimum Cable Diameter Of 1-1/2" (38.1 Mm) And A Maximum Of 2-1/4" (57.1 Mm)
Designed To Fit Over Common Guy Wire Dead-End Pole Fittings • Extended Dead-End Loop Reduces The Need For An Extension Link • Optimized Compact Length That Allows For Fast And Easy Installation
Can Be Used On Most Brands Of Adss Cable That Have Low Strengths And “Standard” Jackets
