GMP 75348 CUTTER RATCHET 556ACSR NO POUCH
Available*
Item # 27252055
Model # 75348
$1,080.35
financing available. Learn More
* Notes on Availability:
(Images may not be of the actual item being sold.)
- Product Description
- You Might Also like
- Recently Viewed
Generic
Class
Group
Type
Manufacturer
LOT
CUTTERS
Tools
Hand Tools
Cable Cutters
GMP General Machine Products
Cable Cutters Small
Warning: This product can expose you to chemicals, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.govProduct Description
GMP 75348 CUTTER RATCHET 556ACSR NO POUCH NEW
GMP 75348 CUTTER RATCHET 556ACSR NO POUCH NEW
P/N 75348 Ratchet Cutter 556ACSR No Pouch Hard Cable Ratchet Cutter 1.6" Overall length 18 in. (457 mm)
P/N 75348 Without scabbard
P/N 75248 Weight: 4-3/8 lbs. (2 kgs) with scabbard
This rugged cutter is designed to cut the following: ACSR power cable up to and including 556 kcmil
500 kcmil hard drawn electrical conductors 1.40 in. (35,6 mm) maximum outside diameter
750 kcmil soft drawn electrical conductors 1.60 in. (40,6 mm) maximum outside diameter
Self-support (figure 8) telecommunications cable 1.74 in. (44,2 mm) with a maximum support messenger size of .276 in. (7mm)
Overall length 18 in. (457 mm)
Note: Do not exceed these maximum cutting capacities for this tool or tool damage will occur.
When cutting with this tool, observe the following important directions:
The cable must enter into the jaws of the tool exactly perpendicular (90 degrees) to the cutting blades so as to result in a circular cross-section cut.
When cutting self-support cable, always orient the supporting strand so it faces the handles for maximum leverage.
If you encounter excessive cutting resistance, use a one click cutting cycle until the cutter moves freely.
Tighten the fulcrum nut periodically and keep the handle bolts tight. The tool will not operate properly unless the fulcrum nut is at least 15 ft-lbs. (20 Newton meters).
Blades made from 6150 alloy steel
Never use this tool to cut electrically energized cable. Severe or fatal injury may result.
GMP 75348 CUTTER RATCHET 556ACSR NO POUCH NEW
P/N 75348 Ratchet Cutter 556ACSR No Pouch Hard Cable Ratchet Cutter 1.6" Overall length 18 in. (457 mm)
P/N 75348 Without scabbard
P/N 75248 Weight: 4-3/8 lbs. (2 kgs) with scabbard
This rugged cutter is designed to cut the following: ACSR power cable up to and including 556 kcmil
500 kcmil hard drawn electrical conductors 1.40 in. (35,6 mm) maximum outside diameter
750 kcmil soft drawn electrical conductors 1.60 in. (40,6 mm) maximum outside diameter
Self-support (figure 8) telecommunications cable 1.74 in. (44,2 mm) with a maximum support messenger size of .276 in. (7mm)
Overall length 18 in. (457 mm)
Note: Do not exceed these maximum cutting capacities for this tool or tool damage will occur.
When cutting with this tool, observe the following important directions:
The cable must enter into the jaws of the tool exactly perpendicular (90 degrees) to the cutting blades so as to result in a circular cross-section cut.
When cutting self-support cable, always orient the supporting strand so it faces the handles for maximum leverage.
If you encounter excessive cutting resistance, use a one click cutting cycle until the cutter moves freely.
Tighten the fulcrum nut periodically and keep the handle bolts tight. The tool will not operate properly unless the fulcrum nut is at least 15 ft-lbs. (20 Newton meters).
Blades made from 6150 alloy steel
Never use this tool to cut electrically energized cable. Severe or fatal injury may result.
